HP OpenVMS Systems Documentation

Content starts here
HP OpenVMS Version 8.3 Upgrade and Installation Manual > Chapter 3 Installing the OpenVMS Operating System

Joining an OpenVMS Cluster

  Table of Contents

  Glossary

  Index

If you answered YES to the question about joining an OpenVMS Cluster, the system now asks a series of questions about your configuration (CI, DSSI, SCSI, local area, or mixed interconnect; the choices depend on which operating system you are installing). If you answered NO to this question, the system immediately runs AUTOGEN, as described in “Running AUTOGEN”. If you answered NO, you can still set up or join an OpenVMS Cluster after the installation is completed by manually running the cluster configuration utility. You can do this by entering the following command:

   $ @SYS$MANAGER:CLUSTER_CONFIG

For more information about cluster configuration, see the HP OpenVMS Cluster Systems manual or the Guidelines for OpenVMS Cluster Configurations manual.

Table 3-2 “Prompts for OpenVMS Cluster Configurations” lists the OpenVMS Cluster prompts and suggested responses. These prompts appear if you answered YES to the question about joining an OpenVMS Cluster or if you manually run SYS$MANAGER:CLUSTER_CONFIG.COM. Note that, depending on your responses and the particular cluster configuration, some prompts are not displayed.

Table 3-2 Prompts for OpenVMS Cluster Configurations

QuestionHow to Respond

Will this node be a cluster member (Y/N)?

Enter Y.

What is the node's DECnet node name?

Enter the DECnet node name (for example, MYNODE). The DECnet node name can be from one to six alphanumeric characters in length and cannot include dollar signs ($) or underscores (_). This is the name you specified in step 12 of the installation procedure.

What is the node's DECnet node address?

Enter the DECnet node address; for example, 2.2. This is the address you specified in step 13 of the installation procedure.

Will the Ethernet be used for cluster communications (Y/N)? (Alpha only)

Enter N for a CI-only or DSSI-only OpenVMS Cluster. Otherwise, answer Y.[1]

Enter this cluster's group number:[2]

Enter a number in the range of 1 to 4095 or 61440 to 65535.

Enter this cluster's password:[2]

Enter the cluster password. The password must be from 1 to 31 alphanumeric characters in length and can include dollar signs ($) and underscores (_).

Reenter this cluster's password for verification:

Reenter the password.

Will MYNODE be a disk server (Y/N)?

Enter Y if you want local disks to be served to the cluster (mandatory for local area and mixed-interconnect configurations). See the HP OpenVMS Cluster Systems manual for information about served cluster disks.

Will MYNODE serve RFxx disks (Y)? (Alpha only)

Enter a response appropriate for your DSSI configuration, if such disks are available.

Enter a value for MYNODE’s ALLOCLASS parameter.

In an OpenVMS Cluster environment, the allocation class value cannot be zero if the node serves DSSI or CI disks to other cluster members, or if volume shadowing will be used on this system. In either case, the ALLOCLASS value must be a number from 1 to 255.

HP recommends that you thoroughly review the chapter on cluster storage devices in the HP OpenVMS Cluster Systems manual. This manual also includes the rules for specifying allocation class values.

Does this cluster contain a quorum disk (Y/N)?

For CI-only, SCSI, local area, and mixed-interconnect configurations, enter Y or N, depending on your configuration. For most DSSI systems, enter Y. However, if you are adding a two-system DSSI configuration to an existing cluster (in which case you might not need a quorum disk), you can answer N. If you enter Y, the system asks for the name of the quorum disk. Enter the device name of the quorum disk. For information about quorum disks, see the HP OpenVMS Cluster Systems manual.

[1] The Ethernet might not be required for communication within a local area OpenVMS Cluster system configured with FDDI devices. Within certain DSSI or CI (computer interconnect) mixed-interconnect configurations, neither the Ethernet nor FDDI are required for communication. If your configuration fits either scenario, you can answer NO (N) to this question.

[2] Cluster group number and password are required by any cluster nodes that use the local area network. In a cluster that uses mixed interconnects, if any of the interconnects require the cluster number and password, then you must set the cluster number and password for all nodes.